Tips –

Category: Tips

How many times in a year you should replace the lamp emergency whether it’s because of damaged or because we’ve never diligently to care for as diligently to do cleanup and charging battery contained therein regularly once a week , for that there is a very easy way so that our emergency lights can last a long time and we can use continuously without the need to perform regular maintenance, doing only minor changes, please follow the steps below:

Prepare tools and materials like in the picture below.

1. Soldering iron
2. Lead soldering and also lotfet to clean the tip of the solder
3. A screwdriver to open the bolt on emergency lamps
4. USB cable
5. Power Bank with a large battery capacity
6. Extension of USB port 4.

After all the tools and ingredients prepared the next step is unpacking the emergency lamp using screwdriver, open all the bolts that hold the casing of the emergency lights, and describe all the circuit and cable contained therein, remember beware lest there is a cable is disconnected or connected short at the time of unpacking.

After all the circuit and cable breaks down with a good next step is to measure the voltage of the battery used in the emergency lights, when the voltage read on the multi-meter/avometer is 5V then lights emergency ready for modification.

Look at the series of PCB found in the emergency lamps, then look at the image below.

The part that was given a circle is part of the cable that has to be modified, for the blue cable is a cable that connected with electricity 220V AC cable, while the red and black cable is connected to the battery, to Blue cable you can eliminate by means of cutting or removing the solder, while for the red and black wires connected to the battery you can cut the core as in figure below.

After the blue cable is removed and the red and black wires connected to the battery in pieces then the next step is to cut the USB cable and peel the outer skin of the cable so that the cable inside the visible, such as a USB cable in General then you will find the content of the cables are red, black, green, and white, and then you can cut the wires are green and white with a red cord and leaving her black just like in the picture below.

The steps were later you can connect the red cable on the USB cable with the red cable that is contained in a series of emergency lights, as well as cables are black, in connecting the cable it is recommended to do the soldering and wrapped with electrical insulation or a burn like in the picture below.

After the USB cable and the cable series on emergency lights is connected properly then you can set him back all the casing and also tidying up the USB cable as shown above, and emergency lights are ready to try. connect the USB cable of yesteryear with the power of the bank that you have and just like in the picture below: emergency lights are lit with a good and durable can be turned on him. The experiment I did for power bank with capacity 5000mAh can light up 8-10 range, of course if your bank power capacity greater then his old emergency light usage will also be longer.

Easy enough right, good luck hopefully dead lights this time doesn’t make you annoyed because it can still get the bright light.

LED emergency lights currently used more electric light lieu society when dead lights.

In addition to practical, LED emergency lights also has other advantages, such as electric power saving, and the light is brighter. Unfortunately, it is difficult to select the emergency lights LED which can be long-lasting.

Most are sold in stores have low quality, ranging from a quick soak, battery LED lights burnt or dead, until the charger burn out. There are some tips on choosing and caring for emergency lights in order to be durable.

Tips On Choosing An Emergency Lights

Customize to your needs. If you want a light easy to carry everywhere then you can choose the type of portable emergency lights.

This lamp has a lot of variety. If you often camping or outdoor activities, choose lights that has a dual function: lighting lamps and spotlights.

Select which has sufficient battery endurance.

Buy emergency lights that have the button light settings.

Note the weight of the lights, if you want to select the emergency lights that light the LEDS use baterei lithium.

Most users tend to choose the emergency lights with a heavy weight assuming will be more sturdy. Weight of the goods does not affect how strong the lights ability.

Notice the design, especially for emergency light that hung on the wall.

How To Take Care Of LED Emergency Lights

After buying the lamp, do not directly used. Do the battery charging until the battery is fully charged. The range of charging time approximately 6-8 hours.

Don’t charging over 12 hours because usually are not equipped with automatic circuit breaker voltage when battery is full. This will result in a battery leak/leak.

If within a period of approximately two months LED emergency lights not in use you should still do the refilling as the first points at least three months.

Do not charge the battery when the electric current in the batteries is still a lot. Did charging when an electric current is really want to sign up, start a flame lamp DIMS and flashes.

Replace the lamp when the edges are already apparent in black stain, because it can inhibit the performance of a series of emergency lights in electronic which may be bad on the battery or the battery is dry inside.

Save emergency lights LED at a steady component incorporates a battery in it are not damaged.

When charging the battery must not be combined with other plugs, such as TVs, refrigerators and so on.

All emergency lights use a battery to power the lamps to ensure continuous availability of the device. These batteries are rechargeable and can be of two types: Hermetic lead batteries (similar to those used in cars), nickel-cadmium batteries and sealed lead acid batteries; These are the oldest rechargeable batteries available today. They are composed of two plates in lead alloy dipped in acid, which breaks the plates producing electrons that give rise to the electricity. More recently, lead battery technology has improved, allowing you to have fully sealed units that do not require the addition of water to keep the acid level balanced. However, it is necessary to provide for periodic substitution. Let’s see how to replace the battery of an emergency lamp.

How many times we have opened the refrigerator and find it completely in the dark, immediately we think that the light has gone away but then we notice that the problem concerns the light bulb that no longer works. Generally each refrigerator is placed with a light source, this like all the lamps after a number of operating hours can interrupt its operation. All the necessary information on how to replace the lamp in the refrigerator you will find them in the steps of this guide.

It is advisable, before proceeding to replace, to make sure that the problem is the light bulb. In fact it is often just the plastic mechanism that crashes. So with open fridge we try to press the button on which the door rests when it closes. If the mechanism is working and even pressing the light will not turn on then the bulb has blown.

It is essential, however, before manipulating any object that works by current, unplug or intervene in the main switch of the apartment. So also in this case to work in absolute safety detach the current. Having done this, we open the refrigerator and locate the position of the lamp, inside of it. This is usually at the top right. We remove the various foods that do not allow us to work in comfort and, make room. In case we have a second refrigerator we have the option to move food.

At this point, we take the screwdriver, usually serves the cross but, the type changes from model and brand of the appliance. Unscrew the lamp cover fixing screws then, remove the cover, taking care not to lose the screws and pull the lamp out.

Of course, we’re going to replace a bulb corresponding to the one removed. When we go to buy it, we present to the dealer that the lamp we need for a refrigerator, then specially built to withstand the cold. However, we keep the receipt in case the lamp purchased is not good for our fridge. At this point we can screw or insert the lamp contacts and, re-position the lamp cover, with the special locking screws. Finally the light is back in our refrigerator and, we no longer have to turn on a light in the middle of the night in order to get something from inside the refrigerator.

We often take it for granted, but lighting at home is fundamental.

To study the positioning and the typology, local per room, according to the function of use, the height of the ceiling, the aesthetics and more, it is useful to not neglect anything and to have always available the right light, especially when it is evening.

In These winter months especially, when the days are short and the hours of light decrease, you realize how much you have an adequate lighting system is basic. But we also think of the emergency situations that can arise, when maybe for a strong thunderstorm or a drop in tension there is a blackout and we remain in the dark suddenly and without warning in our house.

Although it is a space that we know by heart, when we no longer have visual references it becomes difficult to reach the landing to see if the current there is present or even just find a lamp or an emergency torch CE allow us to intervene to Restore artificial light.

For blackout we mean the temporary suspension of the electricity supply, the one that in the house allows us to operate lighting, but also household appliances of various kinds.

Discomfort is always important: You do not orient yourself, you feel helpless and not safer.

Also if the appliances were functioning and normally attached to the current, they stop and if the current does not return in a matter of minutes, you risk having to throw food supplies in the fridge or freezer for example.

In fact the autonomy is a few hours, closed fixture, but no more. Moreover, especially when it is dark outside, you notice how until the current is not returned, it is impossible to do any activity: work, clean house, cook, etc.

For all these reasons we must never overlook the importance of having one or more emergency lights, which can be fixed, attached to the wall or to the power sockets, or even mobile, such as torches or portable lamps.

LED emergency lamps and pull-out torches

A good solution, practical and functional, is represented by the emergency lights extractable.

The advantages lie in the fact that we always know where to find them and how to reach them.

At this point we can extract and use them to make our way and illuminate the spaces, avoiding to stumble and to bump into obstacles and impediments.

A first example of this typology is represented by a Linergy, portable and LED emergency lamp.

This perfect emergency lamp can be installed inside a frame that can be of different colors: white, grey or black, to get married perfectly with the other plaques of the house.

Two versions available: two or three modules.

Installation and assembly are easy because it fits the ignition plates that we have at home.

Discreet and tidy, it lives in the plaque but at the need, when it is able to illuminate the house following an annoying blackout, it extracts pulling from its base and carries it with itself like a portable and autonomous torch for a duration of two hours with a recharge of 12 Hours.

Its battery recharges and replaces its exhaustion.

It doubles its function because it can remain always on, using it as a stair of blue color or lighting only in case of emergency.

This ensures the safety of knowing that in case the light jumps, even for a short time but leaving us in the dark, where to go to find a light always available.

The extraditable torch is combined with the socket and can serve us as a luminous reference even when the house is dark.

It works with LED light and lasts 2 hours.

Stair and emergency lamps functional even in case of blackout

Technologist offers a line dedicated to emergency lights such as Giotto, stair LED lamp and activation in case of current failure in the house.

Illuminates the environment with LED lights of white and high brightness, at 100% in emergency and 30% as night light.

It can be easily switched and operated with simple batteries. Consumes little and the emission of heat is very low.

Another built-in model is Galileo and is available in more colors to suit the style of the house or room/hallway that hosts it.

To ensure safety and immediate help in the moment of need, which as we have already said coincides with unpredictable episodes of Blackout, it may be advisable to equip your home lighting system with lamps for the emergencies that are lit at the moment of the current failure.

This is possible because we are talking about lamps that work with an integrated battery, guaranteeing up to three hours of light and autonomy.

An emergency lamp even has an integrated and extraditable torch, easy to handle and useful to guide us and move even in the different floors of the house, in the many rooms for a considerable period of time that is generally enough to Guarantee the necessary light until the normal functioning of the electric current is restored.

Emergency port Lamps

Avidsen proposes a whole range designed specifically to bring light where it is needed, in every context, situation and circumstance.

The Spotlight line boasts new-generation lithium batteries that will be a very important support in the absence of light.

Compared to lead, lithium batteries tolerate many more refills, have a longer lifespan and involve reduced savings, both from the point of view of environmental and economic impact, on our finances.

This new range consists of three products, soon for sale both in the stores and on the online portal.
The Spotlight model 1w LED is a portable lamp with suspension hook and magnet that facilitates the fixing of emergency wherever it serves.

If you want you can hang on the shoulder, to follow us by light in our every movement in space, in the House, as well as in the cellar or outside.

The autonomy is three hours with high light and up to 10 if in low light mode. The brightness varies from 40 to 90 lumens.

It always works with LED light also version 3w led and portable.
This is also made of ABS with a non-slip handle.

Here the duration is still higher: of four hours frontal and of eleven direct, with a brightness from 70 to 200 lumens.

Finally Spotlight 5w is the top of the range proposed by Avidsen, with lithium battery as always rechargeable and flashing as an emergency light.

The autonomy at high light is 5 hours, of 12 when it is used lower and 120 hours in emergency situations, to 14 lumens in the latter case. The brightness of the frontal light goes from 140 to 360 lumens. All the lamps can also be charged in the car.

Whether in the home or office area, where you work on your computer or have to consult documents, it is essential to be able to rely on adequate lighting.

In the summer, in fact, the long days help us to work, relying for many hours to the only natural light. But in the other months of the year or where the desk is placed in a corner not really exposed to light, or even when the houses are dark, it is crucial to intervene creating lighting points designed precisely to turn on the work table.

The table lamps can have different shapes, sizes and heights, can be fixed or adjustable, thanks to the extensible arm. In any case the choice of work lighting should not be neglected. In addition to functionality, we can find many innovative and design proposals, able to combine aesthetic taste and adequate performance.

Transparent table Lamps

An original proposal, very airy and certainly appreciated by those who follow the lines of the most trendy fashion home or want an iconic table light is the transparent lamp.

The advantages of this type of desk lights are many: in the first place they are adapted to different environments, from classic to modern furnishings.

A transparent lamp creates a pleasant contrast if placed on an antique wooden desk, as on a secretariat, but it will also be perfectly located in a minimal and contemporary studio.

The versatility of these objects continues to please a lot: it gives the idea not to clutter and close the space, because at first glance it is almost invisible, until it turns to the need, emanating a clear light and direct on the workstation.

A first solution is the Bourgie table lamp designed by Ferruccio Laviani for Kartell. This pure design object is still one of the most appreciated and most sold pieces by the company.

To conquer, of this lamp, is the magic and successful combination of Baroque, rich, important and irony form and the modernity of plexiglass. The lamp develops vertically with care in detail, to return an opulent object and strong personality.

To overstay the whole composition is the lampshade, made with pleated workmanship, beautiful to see and surprising for the game of reflections that creates when it is on.

This lamp is not static, but you can choose between three different possible heights, from 68 to 78 cm, depending on the beam of light we want to get, more or less close to the sheet or the computer.

In addition to the Home Office area, you can find a good location even on a dresser, to create a light and atmospheric point of passage, perhaps in the hallway, or used in the bedroom or on a table in the living area as a complementary and scenographic light.

Of Kartell is also the Taj lamp, designed by the designer of the previous proposal, but diametrically opposed by line and spirit. Modern, minimal and no frills, it consists of a curved line, as a three-dimensional sign.

Taj works with LED lights: a powerful and energy-saving light comes out of a lamp so discreet. The transparent variant is called naked, to recall a bare, light, essential and design trait.

Those who love transparencies will also appreciate the new generation version of Fat-boy’s Table lamp.

Transloetje, like her sisters in other colors, recalls for the simple form the table lamps or bedside tables of the past, but revisited in a modern key.

The characteristic is the fact that the lamp is wireless and therefore portable, practical to move from one room to another to make light where and when needed: on the desk when working, in the living room for reading, in the room as Abatjour.

In addition to the transparent version here considered is available in other color variants.

The light bulb is the real protagonist, at sight, as it is placed in the center of the structure and stands out in transparency. The switch is integrated and the lamp operates on battery. All in PVC, both transparent and with pastel color nuances, always clear, it lends itself both to a place inside the house and outside.

Extensible Table Lamps

The lamps traditionally most common for the desk are those with swivel and extensible arm, designed to illuminate the work area closely.

The volley aluminum model of FontanaArte designed by Odo Faulkner is suitable for those looking for a classic but colorful, modern and certainly useful solution for the work.

Although rather simple in the line, it boasts an advanced technology based on touch sensors that serve to turn it on, turn it off and adjust the intensity of the light beam and LED light. Accompanying the arm you can point the light precisely on what we are interested in luminary, choosing also the intensity according to the natural light that changes with the passing of the hours of the day.

The softer accompanies, while the more intense level of the four replaces the natural light when the sun goes away. Little cumbersome, agile, intelligent and light is a solution of great value.

Very original, in combining tradition and novelty, it is the lamp Wood Muuto, a reinterpretation in an ironic and innovative key of the lamp used by architects, with an extensible arm to better adapt to the needs of those who work at the table.

All in wood recalls the northern European tradition, in Scandinavian style, very current in the interior design of these last years: it has details of style at sight, as the screws that stand out in contrast and the power cable in colored rubber.

Original lamps for the desk

Satisfied with the more traditional office workers and lovers of transparent design, we discover some original models of table lamps, able to fulfill their function, also contributing to furnish the room with taste and a touch of novelty.

The Draw lamp by Doiy, is really an unusual choice: although made of ceramic, it contains a light bulb in the light bulb. In fact, the real flash that radiates the light emerges from a hole placed on a ceramic tablet.
The optical effect is really innovative, creative and fun. But the original aspects do not end here: The table lamp can be customized in a thousand different ways because the perforated surface where the light comes out is a white table, made to be drawn and decorated.

You can indulge and return children by choosing to hatch the drawing or the preferred silhouette, which can change as many times as we want.

The appropriate pen is cancellable and is directly in the packaging of the Draw Lamp.

We conclude with a very special object, the IC T1 table lamp proposed by the Flos brand and designed by Michael Anastassiades. Here the object does not recall the traditional lamps with extendable arm, but it represents a unicum.
The light radiates from an opaque blown glass sphere, a sort of crystal ball that reminds the world of artists who perform by moving and dancing on their body, with smooth and perfect movements. The result is sophisticated but sober, versatile and tasteful, suitable for those looking for something really different from the usual.

The sphere, which seems almost suspended, is supported and accompanied by a very thin and elegant brass stem. It seems to be able to keep it in balance by serving the fulcrum of composition. ©2018. All Rights Reserved.